RasuunDrive® UHV 19mm – Type 1
The RasuunDrive® UHV 19mm – type 1 micro linear actuator system offers a travel range of 25.5 mm and was specially designed for use in ultra-high-vacuum environments and is therefore dry-lubricated.
The system is driven by a stepper motor with 200 steps per rotation in an open loop control.
Directly connected to the motor is a low-backlash CoograDrive® gear with a reduction ratio of 80:1 by means of which a likewise dry-lubricated ball-screw drive with a pitch of 0.5 mm is driven.
Benefits
1) Dry lubrication due to coatings
2) Use of high quality materials
3) Custom designed housing
4) High adjustment force
5) Ball screw
Technical parameters
The values shown are based on calculations and measurement procedures carried out by Micromotion GmbH, which are carried out according to the current state of the art. Our definitions can be found at www.micromotion-drives.com. For further information please contact sales@micromotion.de.
Nr.
Parameter
Symbol
Value
Properties
P-001
Vacuum suitable
HV
P-003
Ratio
i
80 : 1
P-004
Self-locking
ja
P-005
Travel range
s
25.5 mm
P-008
Repeatability unidirectional
0.75 μm
P-009
Repeatability bidirectional
3 μm
P-010
Accuracy
20 μm
P-012
Resolution
0.03125 μm
P-014
Lost motion
7.5 μm
P-015
Backlash
0.01 μm
P-016
Rated force
F
50 N
P-017
Peak force
F
50 N
P-018
Momentary peak force
F
50 N
P-023
Rated speed
v
0.01042 mm/s
P-024
Maximum speed
v
0.01042 mm/s
P-034
Lifetime for rated operation
300 h
P-035
Radial backlash output shaft
0 μm
P-036
Axial backlash output shaft
0 μm
P-044
Max. axial load on output shaft (non-operating, impulsive load)
F
50 N
P-055
Moment of inertia
I
900038 * 10-4 gcm2
P-056
Weight
m
151 g
P-057
Min. permissible ambient temperature (non-operating)
T
-20 °C
P-058
Min. permissible ambient temperature (operating)
T
-10 °C
P-059
Max. permissible ambient temperature (non-operating)
T
150 °C
P-060
Max. permissible ambient temperature (operating)
T
120 °C
P-099
Additional technical data
no limit switches
Motor data: Stepper VSS 19.200.0,3-UHV-4LP-2g5 dry lubrication
P-100
Motortype
Stepper
P-102
Maximum speed of motor
n
100 rpm
P-105
Holding torque of motor (unpowered)
T
0.9 mNm
P-109
Rated current of motor
I
300 mA
P-111
Rated voltage of motor
U
42 V
P-112
Phase resistance of motor
R
6 ohm
P-113
Inductance of motor
L
2.2 mH
P-115
Full step angle of motor
1.8 °
P-116
Angular accuracy of step of motor
±0.09 °
P-117
Electrical time constant of motor
t
0.367 ms
P-118
Max. coil temperature of motor
T
300 °C
Data limit switch
P-302
Configuration Limit switches
no limit switches
Spindle data: Ball screw 1214./0,5.3.35.42r ts (uhv) – 25 mm travel range
P-402
Pitch
R
0.5 mm
Data linear bearing LSAGT8
P-601
Max. lateral force in y-direction (non-operating, constant load)
F
1330 N
P-602
Max. lateral force in y-direction (non-operating, impulsive load)
F
439 N
P-603
Max. lateral force in y-direction (operating, constant load)
F
1190 N
P-604
Max. lateral force in y-direction (operating, impulsive load)
F
396 N
P-605
Max. lateral force in z-direction (non-operating, constant load)
F
1330 N
P-606
Max. lateral force in z-direction (non-operating, impulsive load)
F
439 N
P-607
Max. lateral force in z-direction (operating, constant load)
F
1190 N
P-608
Max. lateral force in z-direction (operating, impulsive load)
F
396 N
P-609
Max. overturning around y-axis (non-operating, constant load)
T
38300 mNm
P-610
Max. overturning around y-axis (non-operating, impulsive load)
T
12639 mNm
P-611
Max. overturning around y-axis (operating, constant load)
T
38300 mNm
P-612
Max. overturning around y-axis (operating, impulsive load)
T
12639 mNm
P-613
Max. overturning around z-axis (non-operating, constant load)
T
22000 mNm
P-614
Max. overturning around z-axis (non-operating, impulsive load)
T
7260 mNm
P-615
Max. overturning around z-axis (operating, constant load)
T
22000 mNm
P-616
Max. overturning around z-axis (operating, impulsive load)
T
7260 mNm
P-619
Stiffness in z-direction
c
28,7 N/μm
P-620
Backlash of linear guiding in y-direction
0 μm
P-621
Backlash of linear guiding in z-direction
0 μm
Material information
P-900
RoHS compliant
ja
P-901
Lubrication of output bearing gearbox
FomblinGRM60
P-903
Lubrication of gear component set
FomblinGRM60
P-904
Lubrication of bearing motor
dry coated
P-905
Lubrication of spindel-nut-system
DICRONITE®
P-906
Lubrication of linear bearing
DICRONITE®
P-908
Material of gear component set
NiFe
P-909
Material of output bearing gearbox
1.4108 DIN EN
P-911
Material of bearing motor
Stainless steel
P-912
Material of gearbox output side
1.4305 DIN EN
P-914
Material of motor housing
Stainless steel
P-917
Material of spindle
1.4108 / CuSn
Graphs
P-019
Alternative products
