RasuunDrive® HighTemp 8mm - Type 1

RasuunDrive® HighTemp 8mm – Type 1

The RasuunDrive® HighTemp 8mm – type 1 micro linear actuator system is a system with extremely short design
that is made possible thanks to a parallel arrangement of linear roller table and gear-spindle motor. As a result, a travel range of 10 mm can be realised with a minimal axial length of 45 mm.
The system is driven by a stepper motor with 20 steps per rotation in an open loop control.
At the core of the actuator is a zero-backlash MaalonDrive® gear with a reduction ratio of 160:1 that is directly connected to the motor and drives a ball screw with a pitch of 1 mm.
One inductive limit sensor monitor the end position on motor side.

Benefits

1) Compact build up
2) Robust control without feedback system
3) Custom designed housing
4) Integrated limit switches
5) Ball screw

Technical parameters

The values shown are based on calculations and measurement procedures carried out by Micromotion GmbH, which are carried out according to the current state of the art. Our definitions can be found at www.micromotion-drives.com. For further information please contact sales@micromotion.de.
Nr.
Parameter
Symbol
Value
Properties
P-003
Ratio
i
160 : 1
P-004
Self-locking
ja
P-005
Travel range
s
10 mm
P-008
Repeatability unidirectional
0.5 μm
P-009
Repeatability bidirectional
2 μm
P-010
Accuracy
23 μm
P-012
Resolution
0.3125 μm
P-014
Lost motion
5 μm
P-015
Backlash
0 μm
P-016
Rated force
F
15.1516 N
P-017
Peak force
F
20 N
P-018
Momentary peak force
F
20 N
P-023
Rated speed
v
1.04167 mm/s
P-024
Maximum speed
v
2.1875 mm/s
P-034
Lifetime for rated operation
1000 h
P-035
Radial backlash output shaft
0 μm
P-036
Axial backlash output shaft
0 μm
P-044
Max. axial load on output shaft (non-operating, impulsive load)
F
20 N
P-055
Moment of inertia
I
282 * 10-4 gcm2
P-056
Weight
m
50 g
P-057
Min. permissible ambient temperature (non-operating)
T
-30 °C
P-058
Min. permissible ambient temperature (operating)
T
-20 °C
P-059
Max. permissible ambient temperature (non-operating)
T
130 °C
P-060
Max. permissible ambient temperature (operating)
T
70 °C
P-099
Additional technical data
Proximity sensor Pepperl+Fuchs NBB0,6-3M22-E2 sensor cable 2m and motor ribbon cable, AG28, 4 leads, 2m cable outlet axial
Motor data: Stepper AM 0820-2R-A0.225
P-100
Motortype
Stepper
P-102
Maximum speed of motor
n
21000 rpm
P-103
Resonance frequency of motor
f
170 Hz
P-105
Holding torque of motor (unpowered)
T
0.17 mNm
P-109
Rated current of motor
I
225 mA
P-111
Rated voltage of motor
U
2 V
P-112
Phase resistance of motor
R
7.3 ohm
P-113
Inductance of motor
L
1.4 mH
P-114
Amplitude BEMF of motor
U
0.267 mV/rpm
P-115
Full step angle of motor
18 °
P-116
Angular accuracy of step of motor
±1.8 °
P-117
Electrical time constant of motor
t
0.21 ms
P-118
Max. coil temperature of motor
T
130 °C
P-119
Thermal resistance of motor between coil and housing
Rth1
4.1 K/W
P-120
Thermal resistance of motor between housing and air
Rth2
65.3 K/W
P-121
Thermal time constant of the coil of the motor
τw1
3500 ms
P-122
Thermal time constant of the housing of the motor
τw2
160000 ms
P-123
Insulation voltage of motor
U
200 V
Data limit switch
P-302
Configuration Limit switches
n.c.
Spindle data: Ball screw MLP-8-SPM0052 – 10 mm travel range
P-402
Pitch
R
1 mm
Material information
P-900
RoHS compliant
ja
P-901
Lubrication of output bearing gearbox
Asonic GLY32
P-903
Lubrication of gear component set
Molykote BR 2 plus
P-904
Lubrication of bearing motor
Synthetic light ester oil
P-905
Lubrication of spindel-nut-system
Fomblin GRM60
P-908
Material of gear component set
NiFe
P-909
Material of output bearing gearbox
1.4108 DIN EN
P-911
Material of bearing motor
Stainless steel
P-912
Material of gearbox output side
1.4305 DIN EN
P-914
Material of motor housing
Anodized aluminum
P-917
Material of spindle
100Cr6

Graphs

P-019
At rated operation,At peak operation,

Alternative products

Flexible integration
Vacuum suitable lubrication
Easy controllability
High adjustment speed
Ball screw
Flexible integration
Vacuum suitable lubrication
Easy controllability
High adjustment speed
Ball screw
Flexible integration
Preloaded ball bearing
Easy controllability
Ball screw
Transmission ratio optimized to torque
Vacuum suitable lubrication
Use of high quality materials
Robust control without feedback system
Zero backlash at optimised fit between speed and resolution
Ball screw
Lifetime lubrication
Easy controllability
Extreme power density
High load capacity of output bearing
High adjustment force
High repeatability
Vacuum suitable lubrication
Preloaded ball bearing
Zero backlash at optimised fit between speed and resolution
Ball screw
Vacuum suitable lubrication
Robust control without feedback system
Custom designed output shaft
Custom designed tool holder
Zero backlash with optimised fit between speed and resolution
Vacuum suitable lubrication
Robust control without feedback system
Zero backlash at optimised fit between speed and resolution
Step with in the range of nm
Integrated lens holder